Ubitx modifications to work with the Nextion screens.

The raduino board behind the display houses an Arduino nano, to fit a nextion screen to your Ubitx board you need to flash a newer firmware to the Arduino!

If your screen allows you to select a com port and set it to nano 328p like and the baud rate, like in the picture below ignore the ch340 and the Arduino IDE steps and scroll down to the Xloader section.

 I found some issues with this so I thought I would share my findings for others that have never worked with the Arduino microcontrollers before, this is updating the Arduino are two diffrent parts that make the nextion screen work

Skills needed:
soldering

Ok before I start I recommend you buy an Arduino nano328p  as they unplug from the board (I recommend buying without the header pins fitted as header pins are fitted to the top of the board), you can find these on amazon and ebay for less than £5. and the origonal nano is there and working should you need to go back to the lcd screen for any reason.

Tools needed:
soldering iron
mini usb lead (not a micro usb)
tools to get to your raduino board if fitted into a case

Software needed:
ch340 driver Here
Arduino IDE here
Xloader here (auters websire not available)

The Driver:

Ok install the ch340 driver is needed for most of the Arduino Nano boards as they are clones and use this driver board. Sometimes this fails to install properly on winnows 10 it informs you of this, restart the installer and click uninstall, once uninstalled click install and it should work.

Arduino IDE:

I did this as im not sure why but I could not get xloader to flash the firmware across to the board until I uploaded a program through the IDE for some reason!

ok on the site there are many ways to use it from a web interface to a windows app or download it and install to the computer. I have tried the app but some of the projects I have made have had issues with flashing the firmware to the boards for some reason. So I downloaded the IDE and installed manually.

If you don’t use official Arduino boards for your projects I recommend making a donation to them for all their hard efforts making the software so you can work with these boards.#

Ok once installed restart your computer.

When its restarted plug the Arduino into the computer, the computer should make a noise saying its recognized it’s been plugged in and the power light should come on and the nano

Now start the Arduino ide.

Click on file on the top menu then go down to examples > basics>blink, the blink text should show in the main editor box.

Then click on tools in the top menu scroll down to Board then a side menu comes out and find nano.

Then in tools scroll down to processor and select the atmega328p (old version) I believe the new version is only on the newer official nano boards)

Also in tools check the port no is correct for the board its easier if there are no other usb connected to the computer at the time

Then below the file menu there are some icons, click on the right arrow next to the tick (should say upload) this will send the blink file to the Arduino details as it goes information will come up in the bottom of the ide and a progress bar will tell you what’s going on.

If you look at the four led lights by the reset button on the board the tx and rx leds will flicker very quickly when it says uploading in the ide at the bottom once done it will tell you what its done and if it was successful

Ok if that works without fault leave the board connected and open xloader

Xloader:

Ok sometimes its as easy to set up xloader you open it and it it works straight off, if your reading this you may be having a bit of fun getting to this point

I downloaded the nano firmware from HAMSKEY and unpacked it, there are two files one for the v2,3,4 boards and one for the v5 board open the correct file to your version Ubitx board and open the read me file and it tells you what file you need for your UbitX.

In x loader

The top line hex file is the file you want to flash to the nano click on the square with the dots to find your hex file and the path for that file once you open it comes up in the white box

Use the drop down menu and select duemilanove/nano (atmega328)

Com port needs to be the port of your nano, the same as you used in the IDE

Baud rate should set when you choose the device but don’t use any more than 57600

Press upload and it should come up with whats happening in the very bottom of program, it should take less than 30 seconds from pressing the upload button, again tou will see the tx and rx lights flash on the board and when they stop the program will confirm if its worked or not.

This nano is ready to swap out with the other nano on the raduino

NOTE: the Nextion screen wont work until you upload the files to the nextion screen, that will be done once I receive my screen